Probe the ABS warning lamp driver circuit. 检测ABS警示灯驱动电路。
Does the DRB show "abs warning lamp diode circuit"? DRB是否显示ABS警示灯整流电路?
ABS warning lamp driver circuit open between the CAB and relay box CAB和继电器箱间的ABS警示灯驱动电路断路
Repairing warning lamp circuit open/ short 维修警示灯电路断路/短路
The warning marker includes solar cells, storage batteries and electrical circuit apparatus for selectively illuminating the light elements during low ambient light and nighttime conditions. 警示器包括太阳能电池,蓄电池,以及在环境低照度和晚间用以发光元件选控的电路器件。
This type of system is active warning systems from photodiode, luminous diode, the circuit and was enlarged circuit. 本系统属于主动型报警系统,由光电二极管、发光二极管、放大电路及报警电路组成。
ABS amber warning lamp driver circuit open ABS黄色警告灯驱动电路断开
The structure of the existing open circuit warner is that: the reed switch and the open circuit warning circuit are connected into a section; 现有开路报警器构造是:干簧管与开路报警电路连接为一分体;
The pressure sensor and temperature sensor control the warning circuit via respective dynamic and static contact, led as well as common dynamic and static contact. 所述压力传感器和温度传感器通过各自的动、静触点和导线以及公共的动、静触点控制的报警电路。
Adopt the warning system of this kind of circuit, convey a lot of alarm signals with a stick of wire. 采用这种电路的报警系统,用一根导线传送多路报警信号。
Moreover, this system contains a warning circuit. When it is in the natural station, the green diode is lightened. The yellow diode will be lightened when the level is below 20 cm. 并设有报警电路,正常情况下绿灯亮,当水位低于下限值20厘米时,黄灯亮;
Hardware framework of the system is based on ISA buses of general PC or IPC, including 12_bit multiplying D/ A conversion, time interrupt, pulse receiving, zero check and on-off and warning circuit. 该系统硬件结构是基于普通PC机或工控机的ISA总线而开发,其功能集12位DAC转换、定时中断、脉冲接收、倍频辨向计数、零点检测及使能报警等于一体。
This paper describes a warning circuit which can display with three colour signals whether the measuring result of industrial instruments is right or not to ensure the normal production. 本文叙述的一种显示告警电路能以不同彩色灯光信号指示出工业仪器检测结果合格与否,以确保工业生产的正常进行及产品质量合格。
A Kind of Special Guarding Against Theft Warning Detector Circuit 一种特殊的防盗报警探测器电路
Design of warning electric circuit for instru-ments 仪器仪表中的报警电路设计
Then is the main part of this thesis, where hardware design and software design is discussed in detail, the hardware design includes the current-acquiring circuit of optical module, warning signal-capturing circuit, optical switch driving circuit etc. 接着是论文的主要部分,详细介绍了自动测试系统的硬件设计和软件设计,硬件设计包括光模块发射端、接收端工作电流的采集电路,高低告警信号的捕获电路,光开关驱动电路等;
The Laser Warning Control and Display Circuit Taking Use of the Neighbourhood Related Processing Technique 应用邻域相关处理技术的激光报警控制显示电路